Recent content by NickolasG

  1. NickolasG

    Mark on bottom

    I even saw it on ice blue 2159xx boats tho..
  2. NickolasG

    Burnt laser repair

    Περαστικά.
  3. NickolasG

    Minimum Rigging

    The only one thing from blocks you need is classic boom vang top block and base, the rest of the rig you can make without blocks.
  4. NickolasG

    ARC 1 and ARC 2 rigs

    Well it’s a quite weird thing to discuss but as I remember back in a day, LP (United Kingdom) was engineering these ARC rigs and parallel to LP, there were guys from PSA (Australia) and they’ve been working on C-series rigs. Both of rigs were made in real life, but as I know only ARC went to...
  5. NickolasG

    Name for the boom's plastic collar that meets the mast pin?

    I guess we call it gooseneck pin and gooseneck plug? I don’t know how else we’d call it At least if you google it this way you’ll find it for sure
  6. NickolasG

    Bent Deck Plate - Why???

    It’s not about mainsheet length, mate, it’s about security line length. Do you set your mainsheet when you’re ashore? I don’t think so, but I’m sure that you set mast security rope, sometimes it’s too short and won’t let mast turn freely when weather shifts, and from the tension that appears...
  7. NickolasG

    Bent Deck Plate - Why???

    Usual reason this plate bends is that mast with security rope on may turn around 1-2 times and due to tension on this rope this thing bends.
  8. NickolasG

    Practic laser dolly

    Theoretically I should have screws in these 2 holes, but they’re missing. Of course I don’t want to take them apart, but I also don’t want them just to break. So, I guess the right solution is to find couple of aluminum rivets?
  9. NickolasG

    Practic laser dolly

    Hello everybody, I’m owning laser set up dolly by practic, it’s less than a year old and recently I just noticed something. At the stands where the belt is connected, on the bottom must be 2 screws and nuts from the inside (I can’t find any picture) and here’s my case. I have no clue how it’s...
  10. NickolasG

    New cover - whats this flap for?

    Α At same time color of boat is grey/dark blue, which’s usually being applied to psa hulls
  11. NickolasG

    My Laser was hit by a car!

    He should, but in the port authority they said like : no it’s not our fault we not gonna do anything (we were speaking English back in a day because the crew of yacht were some people approximately from Germany/Denmark or Finland and we were Greeks, this is why I remember everything word-word
  12. NickolasG

    My Laser was hit by a car!

    Last September my Laser was hit in the sea, while training. There was a gust and we were going downwind, I got capsized and literally out of nowhere appeared 15m Sailing yacht, they were going on engine power and my coach saw him getting closer and closer to me and not paying attention at all, I...
  13. NickolasG

    Laser Kicker With New Allen Top Block

    I’ve tried 3 of them. The new Allen one, classic harken and the one that comes with Allen vang(kickers). From my experience I can tell u that the classic harken top block was the best one and the smoothest one and it resisted a lot of high loads (I’m sailing ILCA 6 or Radial, call it however you...
  14. NickolasG

    Tiller separation

    Thank you all for advising! I really appreciate it. Will tray all of the ways that we’re described here ASAP, when I’ll come again to my YC
  15. NickolasG

    Tiller separation

    Nice question how it happened. I don’t know how. Probably it was in ok position but somebody hit my boat from stern and tiller has gone from its position. As you can see ok the pictures tiller isn’t exactly in the center, it’s a bit left. edit Do I need any lubricant ex. WD-40? to decrease grip?
Top