You have a $200 boat. I'm assuming the condition is consistent with both the price and the picture above. I would concentrate on getting use out of this boat and not spending any more money or time on it than necessary.
I would clean up that mess above so that it is waterproof, not worrying about a bailer. I you get some water in the cockpit, put up with it. No need to shell out top dollar for updated rigging, especially if you aren't racing. Rig up something new with some spare blocks.
Sail this boat. Enjoy it. Don't spend more money on it than it's worth.
Oops, getting use to replying on this site. I took it out on it's maiden voyage today. 60 degrees air, 55 deg water. Light winds, but it soon became apparent that I will need either a ratcheting main block and/or gloves to handle the sheet. the boat was okay for 30 min or so then started to act sluggish and roll without prompting. A Leak! I headed for shore 1/2 mile away and luckily had enough wind to get there. Upon beaching, I found I could not lift the stern. i drained it for 45 min. before being able to get it on an incline to fully drain it. I figured I had at least 50 gallons of water in it. The aforementioned cockpit drain which I assumed was plugged with epoxy was letting in water at a very fast rate from outside the hull . I returned home and did a water leak test and sure enough, that was the problem. Does anyone have a good idea on how to seal it temporarily so a future owner could possibly fix it or me?You have a $200 boat. I'm assuming the condition is consistent with both the price and the picture above. I would concentrate on getting use out of this boat and not spending any more money or time on it than necessary.
I would clean up that mess above so that it is waterproof, not worrying about a bailer. I you get some water in the cockpit, put up with it. No need to shell out top dollar for updated rigging, especially if you aren't racing. Rig up something new with some spare blocks.
Sail this boat. Enjoy it. Don't spend more money on it than it's worth.
The rest of the boat is fairly solid with some spider cracks around the bow, mast step, hiking strap plate area, etc.What's the rest of the boat look like?
If the deck is stiff, then go for a permenant repair. From the picture, it appears that you will have to do a fair amount of grinding to get all of that crud out of the cockpit drain area. This may necessitate painting the area with something like Easypoxy or gelcoat.The rest of the boat is fairly solid with some spider cracks around the bow, mast step, hiking strap plate area, etc.
How do you determine a stiff deck? I have the cockpit drain area repaired, auto bailer fitted and waiting for my brass thru hull fitting to arrive before drilling the hole and putting it all together. I have attached pics of my repair, and an inside pic of how I bonded the cockpit to the hull with masonary caulk at the corners, and thickened resin around the drain hole. I'm pretty sure I will not have any movement between the two. Also, when weighing my hull to determine how heavy it is relative to a new hull that supposedly weighs around 130#, do I include dagger and rudder/tiller?If the deck is stiff, then go for a permenant repair. From the picture, it appears that you will have to do a fair amount of grinding to get all of that crud out of the cockpit drain area. This may necessitate painting the area with something like Easypoxy or gelcoat.
You'll know when you've sat on one one that is stiff and one that has some give. Essentially, what happens is the three layers that make up portions of the deck where deflection (bending) resistance is required (next to the cockpit, foredeck, etc.) can become delaminated. That is, the outer layer, the foam core, and the under layer become separated and no longer have the strength to support your weight when sitting on the deck. Another way to tell is if the deck on each side of the cockpit looks slightly concave. Regarding your repair, I have uploaded a couple of simple sketches showing how I have permanently bonded the cockpit after bulkhead to the inside of the hull. This illustrates the second one I did and it is easier and allows for more air and water to flow under the cockpit. I cannot determine from the pics you posted how you made the repair, but it does not look like you used anything more than unthickened epoxy. IMHO, this will not hold.How do you determine a stiff deck?
As I always tell my wife, "It's therapy and keeps me off the streets." BTW, can you get Carib in Texas?If you want to make a winter project out of it, would be fun (I'm a dork like that).