Search results

Hi John, I tried phoning you a few times today - starting at 8:30 am east coast time. This was probably much too early if you were in AZ at that hour. If so, my sincere apologies for that. I can tell you that the boat does not have a trailer, but I would like to talk with you if you are still...

Hi again, Steve. After I received your message, I have had a couple of inquiries about the boat - and just wanted to answer any questions that you may have while I am in that mode. I am very eager to sell the boat and will make every effort to agree to a fair price that we can agree on. Many...

It is still available and I would be happy to show it to you at your convenience.

J/24 For Sale – Cataumet, MA 9/15/23 Hull #4249 (built in 1986) is being offered for sale, fully found, with many new and recently refurbished features. “Waltzing Matilda2” is in the water in Red Brook Harbor. This boat has many new and upgraded features and includes many of the later model...

Hey Dan! Great to hear from you. In short, I gave up on finding the plate (which I am sure is the best configuration for securing the outboard to the transom and still having the flexibility to raise & lower it), and I just bought a new "standard" bracket with the same old raising and lowering...

Thank you very much! Great input and advice - much appreciated!

Thank you for following up on my request. Turns out I found a pretty good Doyle Dacron #1 jib that is cut for furling and has rope luff. So I am all set! But many thanks!

Hi all - Here's a modest request for a decent #1 genoa. I discovered that my J/24 'project' boat has a pretty good #3 jib (working jib) for my Harken furler (yep, that's what I have). Everything works fine with the jib that came with this boat, but the sail is a little small for those light...

I can’t send a picture - the boat is in storage in MA and I am in North Carolina until May. But the ‘lowers’ are the bottom end of the split backstay - I.e. the two sections that branch off of the upper backstay and attach to chai plates on each rear corner of the deck. I would need the entire...

Hi Jamie, Would you happen to have lower back stays available? I could use one or both if you have them. Many thanks - and sorry for you having to do this! Bill

Hi all - Just wondering if anyone has a good recommendation for material that can be used to fabricate replacement gaskets for a new compass (Ritchie Helmsman) and a RayMarine depth sounder. I have templates, just need a material that can be cut to make good watertight gaskets for these...

Sorry. No results yet. Boat finally made it into the water and still getting roller curler and mast step location squared away … But I’ll contact you when I’m installing the depth finder.

Hi Tide Eyed - My sincere apologies for the embarrassingly slow response to your messages. In addition to trying to get my boat into the water, we have welcomed our first grandchild - a boy - into our lives. My daughter gave birth on July 1st and she and my son-in-law and child all arrived on...

Thanks so much for getting back to me so quickly! The commercial plugs and shims are so expensive, and for such a simple - but essential - purpose. I'm going to make some of my own shims, but would rather have use of someone's surplus that have been successfully used. Thanks again, Bill

Would you, by any chance, have any of the spacers that secure the mast in the hole in the deck? I will take any that you might have. Thanks! Bill

Thank you, Vince. I wondered about the necessity of the additional purchase for a J24. I had a pretty hefty system for backstay tension on my J30 - but it was a heavier rig and required a greater force to bend the mast. Nothing in the pulley system led forward - everything was a maybe 5:1...

Thank you, Dan! This is very helpful - a great photo that shows a nice setup for a lifting engine bracket. The main feature I noticed is the plate that holds the mounting bracket - also a Garelick product, if I'm not mistaken. The plate adds more rigidity and heft to the entire bracket...

Just loaded up my outboard in prep for launching my ‘project’ J24 tomorrow - and discovered that my engine mount (bracket can be raised and lowered) is so worn out that the engine wobbles all over. My 3.5 HP Mercury would be totally unsafe for almost any conditions - and so I am faced with a...

Hopefully, you received my previous message - sent at 11:16 pm last night. Please advise if you received it and whether adding the other lower backstay is feasible. Thank you! Bill

Hi again - It occurred to me that it might make sense for me to buy your other lower - the one that is missing the lower turnbuckle and rod. I may actually be able to use it as well (since I do have a usable lower turnbuckle and rod). Since it isn't of much use to you, would you mind...