Recent content by knoxSAILS1's&2's

  1. K

    Looking for a Laser 2 Rudder Assembly

    As rudder blades go,Intensity sails sells them via Ebay, and they are made in Portsmouth RI by a boat Manufacturer near PerformanceLaserSailcraft, and the rudder is $200; http://www.ebay.com/itm/Rudder-Blade-Laser-ll-Sailboat-/310177437168
  2. K

    Looking for a Laser 2 Rudder Assembly

    Buy if from American Sail as they sell the 14.5 and its pintles ar 6 1/4 spaced and 3/8 diameter on gunguns, and the blade is a direct down near copy of the original Laser 2. The head is much less than an original also. a picture is at this link...
  3. K

    Mast for laser 2

    Close to NH, Have several Masts, and full Laser 2s.
  4. K

    I have several here in NH. Need spinnaker ready or not? I think shipping logistics would mean a...

    I have several here in NH. Need spinnaker ready or not? I think shipping logistics would mean a commom carrier, like R&L, UPS fright, or FedEx Freight. I have a Fed Ex account and could check them for cost. If you need just a lowwer bare aluminum I believe either Selden Spars, or Dwyer Aluminum...
  5. K

    Field Trip to LP Rhode Island!

    It is only to obvious, as what I have realized from two years of asking for instructions to install a Laser 2 Spinnaker launch tube (Zero Help!), from not only the help at RI Performance Laser store and Corporate Customer service, is that incompetence and disregard for the customer base is...
  6. K

    Laser 2000 For Sale

    Is it available? Asymmetric Spinnaker ready? Pictures possible?
  7. K

    Laser 2 w/ Spinnaker and Trapeze

    How is the bulkhead across the inner hull at the fore cockpit, and fore deck stiffener stringer, as well as the other wooden segments that support the cockpit floor holding up? I ask because I see so many ports that would indicate work was done. Did you need to glass new plywood in? I have a...
  8. K

    1987 Laser 2 for sale

    Wonder if th club would part with it in trade for a ready to sail new rigged and refinished as needed in cockpit edge area (professionally done) Laser2 in fantastic shape. I want to get a Laser2 with the spinnaker launch tube, if theirs comes this way. I single-hand the Laser2 and the tube is...
  9. K

    1987 Laser 2 for sale

    Have it in NH
  10. K

    message would not fit. Email is knoxsj59@comcast.net Saved message for you in draft's awaiting...

    message would not fit. Email is knoxsj59@comcast.net Saved message for you in draft's awaiting your email to send it to. Regards, Stephen
  11. K

    (603)622-5129 Steve in NH if you want to get talked through the repair. I have four L2's in th...

    (603)622-5129 Steve in NH if you want to get talked through the repair. I have four L2's in th works now. Just wrapping up the first. Sold many used and refurbished Lasers this year, I did glass work to. The Laser2's are more difficult, I find. Wood panels must be replaced in pieces, and the...
  12. K

    Laser 11 construction/repair

    The trunk will always leak if you don't completely remove the cockpit floor around the broken trunk. Make a cut surrounding the area and lift it out, back grind/sand the under edge of the opening, and of the extracted under side of the area to repair. Make a epoxy repair to the broken trunk...
  13. K

    Look for rudder head and lower mast

    Have the head in NH $50, Mast is way to expensive to ship to Canada though.
Top